Q:will this truss kit work on a 1989 kingpin ford dana 60?
Asked by: Kevin
- 10/15/2017
A: Yes this Truss kit includes All the brackets necessary for the Kingpin front 60 ('85-'91.5) or Balljoint front 60 ('92-'97) axle to swap into a Jeep TJ Wrangler ('97-'06), LJ Wrangler ('03-'06), XJ Cherokee ('84-'01), ZJ Grand Cherokee ('93-'98), and MJ Comanche ('85-'92)
Was this answer helpful?
6 of 7 Customer(s) found this Answer helpful.
Q:Just wondering if this comes as a kit or if its pretty much assembled when you ship it? I love the design and idea, but I'm looking to narrow a d60 by 4" to keep my cherokee a little narrower.
Asked by: Kolby
- 1/10/2017
A: This comes as individual pieces you could likely customize it to your needs.
Was this answer helpful?
3 of 4 Customer(s) found this Answer helpful.
Q:So will this not work with my xj using the rubicon express radial arm kit, if not i guess im just wondering why?
Asked by: Sam
- 3/15/2017
A: Radius arms have a short UCA that is attached to the LCA. Since the pumpkin is much larger on these axles, the UCA mounts on top of the axle must move up. The RE UCA are not long enough and are mounted too close to the axle on the LCA so the angle is extreme and it contacts the pumpkin. You could make new UCA that mount further back on the LCA and are longer and it could work.
Was this answer helpful?
3 of 5 Customer(s) found this Answer helpful.
Q:Does this kit come with the lower control arm mounts. And if so are the 90* as in straight ?
Asked by: Josh Gerry
- 5/2/2017
A: They are angled in towards the frame. Since these axles are much wider and the LCA brackets are wider than stock, the brackets are angled in more to compensate.
Was this answer helpful?
3 of 4 Customer(s) found this Answer helpful.
Q:How much modification will it take to make this kit fit a Ford 78-79 Kingpin?
Thank you
Asked by: Derek
- 3/6/2017
A: This is not recommended. The 78-79 pumpkin is much more centered on the axle than a newer kingpin. This will change where the UCA lines up among other significant issues.
Was this answer helpful?
1 of 4 Customer(s) found this Answer helpful.
Q:Just wondering if this comes as a kit or if its pretty much assembled when you ship it? I love the design and idea, but I'm looking to narrow a d60 by 4" to keep my cherokee a little narrower.
Asked by: Kolby
- 1/10/2017
A: This ships as a kit that will need to be fully assembled and welded
Was this answer helpful?
0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Tom Kellough (12/30/2020)
A: This comes as a kit that needs to be assembled and welded
Was this answer helpful?
0 of 0 Customer(s) found this Answer helpful.
Q:If ordering the 3 link, is it possible to weld the upper link to the truss right above the center housing, or is the three link bracket only designed to be ran from the passenger side upper arm location?
Asked by: Curtis Miller
- 9/11/2018
A: It is possible however usually packaging becomes an issue and that leads to lots of extra work. There's a lot going on in that area and usually the passenger side only needs exhaust modifications to work. The upper link mount will likely need to be cut down so it's as low to the truss as possible.
Was this answer helpful?
0 of 0 Customer(s) found this Answer helpful.
Q:I see this truss has some notes to some fitment issues. Will this truss be compatible with a rough country 6.5 lift or will I need to get rustys off road 4 link kit and build a custom kit around that? Or will I be forced to go with a 3 link?
Asked by: Thomas
- 12/30/2020
A: This kit was intended to work with a True 4 link or 3 link suspension Radius arms typically do not work due to the width of the Lca mounting location and vertical separation with the upper control arm
Was this answer helpful?
0 of 0 Customer(s) found this Answer helpful.