CYBER WEEK Show Details CYBER WEEK Hide Details
(0) Item / $0
Call: 855-278-3299 | Hi Guest, Login! |

  

JK Front Axle Truss

JK Front Axle Truss

Your Price:$139.99
In Stock
Part Number:JK4401BASE

Choose Options

Axle model
JK 44 Axle
JK 30 Axle
Also available from these fine distributors

JK front axle TRUSS

This heavy duty and light weight truss system and armor is designed to take serious abuse and reinforce your front 30 or 44 JK axle. The 1/4" thick truss top and 10Ga. gusseting incorporates a unique design to strengthen both axle tubes, not just the long tube (commonly found in "other" designs). The precision cut and formed components of this setup ensure a hassle-free installation.
 
 

Features include:

  • 1/4" and 10 gauge (.130") mild steel. Precision CNC cut and bent for great fitment.*

  • Truss is low profile to allow clearance above the axle.

  • Truss spans length of long side AND short side.

  • Truss is reinforced using interlocked 10 gauge thick gussets for maximum strength and easy assembly.

  • Overall low profile design means your axle is stronger, sleeker, easier to fit into any vehicle, and less likely to interfere with vehicle components.


THIS KIT IS INTENDED FOR VEHICLES WITH AT LEAST MINOR LIFTS. IF USING WITH NO LIFT, CHECK CLEARANCES BEFORE INSTALLING. NOT TESTED IN NON-US JKs WITH DIESEL ENGINES or RIGHT HAND DRIVE AXLES.**

NOTE: This kit requires general welding and fabrication skills including welding to the cast center section. Welding should only be done by a competent welder. Artec Industries implies no guarantees or warranties and is not liable for improper installation.
*Some grinding and fitment may be required when installing this kit. Every axle varies slightly and some fabrication may be required.

** In rare and extreme cases, the truss may come into contact with oil pan. Prior to operating the vehicle, remove the coil springs, cycle the suspension including full compression of both sides simultaneously and add bumpstop extensions to prevent damage to oil pan.

5 Stars
jk d30 truss
1.easy to install 2.quality is 2nd to none 3.a must have for d30 with big tires 4.awesome price!
Did you find this helpful?  9 of 11 Found Helpful
Reviewed by:  from scranton pa. on 5/11/2015
5/5
5 Stars
shop foreman
great product easy fit if your looking to beef up your diff assemblies a must for a dana 30 recommending to my customers on both the dana 30 and 44 with larger tires
Did you find this helpful?  8 of 10 Found Helpful
Reviewed by:  from las vegas. on 9/30/2014
5/5
5 Stars
Great fit.
Just installed in my '07, Installed with the axle on the vehicle and had zero warpage. Definitely more confident on the trail.
Did you find this helpful?  6 of 7 Found Helpful
Reviewed by:  from Grovedale, Alberta, Canada. on 10/16/2013
5/5
5 Stars
2013 Jk truss
Installed this along with the artec raised trackbar bracket to use with my synergy drag link flip. The quality of the machining is second to none as well as the fitment! I'm glad I went this route over an internal or external sleeve as it simply makes the axle more robust by adding lateral strength and integrity. Zero clearance issues, strength to handle 37's, and cheap insurance, makes this a powerful trifecta that Artec delivers with amazing customer service and support! I hope to truss the rear soon and will be doing so with Artec products!
Did you find this helpful?  4 of 6 Found Helpful
Reviewed by:  from La Mirada, CA. on 9/18/2013
5/5
5 Stars
Jeep JK Axle Truss
The truss I ordered came promptly, it was as described and the fit was perfect. This is a quality product that enhances the durability of my Jeep axle. I won't hesitate to do business with Artec Industries again.
Did you find this helpful?  3 of 5 Found Helpful
Reviewed by:  from Burbank, CA. on 7/1/2015
5/5
5 Stars
JK Front Truss
Take your time welding and preheat your center section. Truss went together perfectly and was actually a really fun project.
Did you find this helpful? 
Reviewed by:  from TX. on 9/9/2019
5/5
5 Stars
Mr
Excellent product that simplifies the 3rd link bracket for my long arm swap. Can never go wrong with artec. Good steong reliable products with excellent customer service.
Did you find this helpful? 
Reviewed by:  from Brownsville. on 7/8/2019
5/5
5 Stars
Mr.
Great Product, easy install, High quality!
Did you find this helpful? 
Reviewed by:  from Maine. on 6/20/2019
5/5
5 Stars
Mr.
Excellent product, I like Artec Industries products because as a hobbyist welder they allow me to save big money on labor and by doing it myself am able to customize things to my needs.
Did you find this helpful? 
Reviewed by:  from Dallas, Texas. on 7/13/2018
5/5
5 Stars
Mechanical Engineer
I just completed an axle swap on my 2003 JEEP Grand Cherokee using a set of JK axles. I built up the Dana 30 front axle using an Artec JK Front Axle Truss. The axle truss is very well designed, and the parts all fit together very well, and match the contours of the axle and differential housing well. I welded the truss using a Hobart 190 MIG welder, using S6 wire. I preheated the differential housing with an oxy acetylene torch to 400 degrees before I welded the housing. The thickness of the materials the truss is made from provide increased rigidity to the axle assembly without adding unnecessary weight. The truss could have been made out of thicker materials - but that increases unsprung weight, and the axle assembly would end up breaking or bending at another point in the assembly, possibly an axle C (where the knuckle mounts).
Did you find this helpful? 
Reviewed by:  from Albuquerque. on 3/7/2018
5/5
5 Stars
Mr
It looks great, easy to install, makes the axle look like a 1 ton set. Such a smart design.
Did you find this helpful? 
Reviewed by:  from Arizona. on 4/4/2017
5/5
5 Stars
07 Jeep Jk
Awesome parts and company, Keep up the good work!!
Did you find this helpful? 
Reviewed by:  from Watervliet ny. on 3/18/2016
5/5
5 Stars
Jk truss
Great product, fit and installation went well. Looks awesome
Did you find this helpful? 
Reviewed by:  from Indiana. on 1/14/2016
5/5
5 Stars
Mr.
Little more fan work than anticipated. But good product overall. Great insurance for stock axle housing
Did you find this helpful? 
Reviewed by:  from kemp,tx. on 9/23/2015
5/5
5 Stars
dude
this is a no-brainer decision if you have tires larger than 35" and want to beef up the D30 for less selective lines while wheeling in the rocks; find a quality shop to burn it on right or if you've got that skill set , the interlocking design combines w/ it's sleekness and lightweight to clear your vital engine bay guts while truly beefing the weakish d30. Let's you get the most from the OEM axle while you save for the big ones....very happy w/this and the Artec frnt lwr CA brackets !
Did you find this helpful? 
Reviewed by:  from NASHVILLE . on 9/10/2015
5/5
5 Stars
Dana 30 truss
I was very impressed with the truss' design. It fits together really well and look like a ton of time went it its creation. The only thing I felt might need attention is the braces that run parallel to axle be upgraded to 1/4 instead of 3/16s. It feels thin, but that could just be my desire to plate everything in 1/4. Great job guys.
Did you find this helpful? 
Reviewed by: (Verified Buyer)  from Albuquerque. on 6/9/2015
5/5
5 Stars
Sweet
Stout! Looking forward to getting this installed.
Did you find this helpful? 
Reviewed by: (Verified Buyer)  from TX. on 12/14/2014
5/5
5 Stars
Great fit
The truss went in with very little grinding. This is my second truss and will come to Artec for my needs in the future
Did you find this helpful? 
Reviewed by:  from Florida. on 8/27/2014
5/5
5 Stars
Great Kit
Even the installer was blown away how easy this kit was to assemble and fit. Welded up great. Only very minor grinding required to fit my RHD JK.
Did you find this helpful? 
Reviewed by:  from New Zealand. on 5/20/2013
5/5
5 Stars
jk front axle truss
great product... perfect fit.. awesome design, gives extra strength to the dana 44 axle where it needs it. fast shipping. nice upgrade everyone should do running bigger than stock tires.
Did you find this helpful? 
Reviewed by:  from maryland. on 3/27/2013
5/5
5 Stars
Dana 30 Artec Truss
Great fit it went together with no grinding. This is the best truss on the market.
Did you find this helpful? 
Reviewed by:  from Attleboro Massachusetts . on 3/15/2013
5/5
5 Stars
JK truss
I love this truss, it fit perfect, which never happens, it looks awesome, and I no longer worry about bouncing my heavy jk over things. I couldn't believe how inexpensive it was for what I got! I would highly recommend this kit!
Did you find this helpful? 
Reviewed by:  from Billings Montana. on 2/8/2013
5/5
5 Stars
Great product
Great fit and of high quality
Did you find this helpful? 
Reviewed by:  from Florid. on 12/19/2012
5/5
5 Stars
Very impressed
This truss is very high quality. All of the pieces are easy to install on the axle. I installed this in combination with the artec track bar bracket and lower control arm skids. I also already had installed inner sleeves and c gussets. I am confident that with the artec truss and other components installed that my rubicon Dana 44 housing is no longer the weak link in my front end and should stack up with the aftermarket replacement housings for a fraction of the cost.
Did you find this helpful? 
Reviewed by:  from Bellevue, WA. on 11/24/2012
5/5
5 Stars
Artec Dana 30 Truss
I installed this truss on my Dana 30 and it went on very easley. It certainly beefed up the axle and it looks very good when all complete. I would givr this product a big thumbs up!!
Did you find this helpful? 
Reviewed by:  from Acton, CA. on 11/19/2012
5/5

Related Items

Recently Viewed Items

Connect With Us
Newsletter Sign Up
PayPalVisaMastercardAmerican ExpressDiscover
3dcart Design by The Cart Designer