5% off as a Kit vs. Individual parts

Our EASY 4-LINK KIT B is the simplest way to get your links done. This kit is based off our most popular parts we've sold our customers for a single triangulated 4-link with angled upper control arms and slightly angled lowers. The brackets available in this kit are combined for easy setup and the upper mounts allow for adjustability. The heat and cryogenically treated chromoly rod ends are the strongest and longest lasting on the market. The included tube adapters feature machined WRENCH FLATS for easy adjustments and tightening and conform to the outer diameter of the tubing it welds to. The included stainless steel high misalignment spacers allow for maximum articulation in the rod end. As an option, this kit offers four foot lengths of both 1.5" and 2.0" tubing to be cut to the exact length needed for your particular vehicle.

Includes:

2 RH, 2 LH - 7/8" -14tpi x 3/4" bore rod ends
2 RH, 2 LH - 7/8" -14tpi Tube Adapters
2 RH, 2 LH - 7/8" -14tpi Jam nuts
8 - 3/4"-9/16" WIDE High Misalignment Spacers
2 RH, 2 LH - 1.25" -12tpi x 1.0" bore rod ends
2 RH, 2 LH - 1.25" -12tpi Tube Adapters
2 RH, 2 LH - 1.25" -12tpi Jam nuts
8 - 1.0"-3/4" High Misalignment Spacers
1 - Pair of Dual 4-link Brackets
1 - Pair Lower Link Axle Brackets
1 - Pair Truss Upper Link Mounts (2.63")
2 - 4 ft 1.5" OD .250" thick DOM tubing (optional)
2 - 4 ft 2.0" OD .250" thick DOM tubing (optional)

SHIPPING NOTE: If selecting PRO KRAWLER Rock Krawler joints, no misalignment spacers will be shipped. The joints will be drop shipped directly from Rock Krawler in New York so extra shipping time may be needed.

NOTE: This kit will require drilling of lower link holes to 3/4" unless you specify you'd like 9/16" bolts for your lower links.

Rating Snapshot

Select a row below to filter reviews.

Average Customer Ratings

5.0

Very nice kit

Well put together pieces make it alot easier to setup a rear 4 link. Comes with everything you need except hardware, which I used 9/16 and 3/4" x 4.5" long. Highly recommended

Did you find this helpful? 8 of 9 Found Helpful

Reviewed by: Brandon Herring from San Antonio, TX on 4/15/2012

Surgical Precision, Surgical Grade

I purchased this kit through a local reseller (Skinny Pedal, Caldwell Idaho). These parts are extremely well built and their fit is precise. One can sense much thought has been given to their design. I am glad Josh talked me into using this kit. My experience so far has me wanting to look at the front 3-link kit next. Thanks all.

Did you find this helpful? 5 of 6 Found Helpful

Reviewed by: Gary Gregerson from Nampa, Idaho on 9/10/2012

Customer

Could not be happier with the suspension. The delivery was fast and we'll boxed as well as the components are topretty notch. My vehicle had some limitations that this suspension worked perfectly with. Brackets are all spot on and match up perfectly.

Did you find this helpful? 2 of 2 Found Helpful

Reviewed by: Matt from Albuquerque on 12/20/2016

Nice complete kit

kit is very complete and adjustable to fit a wide variety of applications

Did you find this helpful? 2 of 3 Found Helpful

Reviewed by: Matt Hodges from West Texas Offroad on 11/17/2013

Great Kit!!!

Very clean and easy to install. Only negative is i had to drill out holes for the lower links, original holes were to small. All in all a great kit

Did you find this helpful? 1 of 2 Found Helpful

Reviewed by: (Verified Buyer) Scott Simonds from Marietta Ga on 10/5/2015

4 link kit

First off this kit is amazingly easy to use artec has made this kit so there is no guessing on how it goes together and the packing is planned out the same I would recommend this kit to anyone

Did you find this helpful?

Reviewed by: ERNEST L Armijo from NM on 3/21/2021

Q: Does this kit work on a 88 jeep wrangler?

Asked by: Josh - 10/15/2015

A: This is a universal kit and designed to work with most vehicles.

That being said, this kit would be best suited for the rear and our Kit A up front.

See it here: http://www.artecindustries.com/Easy-4-Link--Kit-A--Triangulated-Uppers_p_271.html

Was this answer helpful? 5 of 5 Customer(s) found this Answer helpful.

Answer provided by: Armando Verdugo (11/20/2015)

Submit an answer

Q: DO I NEED A TRAC BAR WITH THIS KIT? I AM USING IT IN THE REAR OF MY JEEP

Asked by: SPENCER - 5/22/2017

A: No, You will not need a trackbar with this kit in the rear of your Jeep.
The links mounted in the center of the axle will keep it from walking side to side .

Was this answer helpful? 4 of 4 Customer(s) found this Answer helpful.

Answer provided by: Tom Kellough (7/17/2017)

Submit an answer

Q: Will ur 4 link kit work with ur 8.8 axle swap truss that's also triangulated?

Asked by: bill - 6/17/2015

A: Yes, it was made to work with our 4 Link Kits.

Thank you.

Was this answer helpful? 2 of 3 Customer(s) found this Answer helpful.

Answer provided by: Artec Staff (7/15/2015)

Submit an answer

Q: Will this kit and kit a work on a 2012 jk? Will I still need a track bar? Any chance on being able to run a different joint like a Johnny joint?

Asked by: Kewlbeansbro - 1/15/2016

A: Yes you can make this work on a 2012 JK, but it may require modifications.

You can certainly use other ends, but you would have to piece all of the brackets and stuff separately as this kit is a simple compilation of the most used options. Each item is sold separately and listed at the bottom of the product page.

Was this answer helpful? 2 of 2 Customer(s) found this Answer helpful.

Answer provided by: Armando Verdugo (1/21/2016)

Submit an answer

Q: Will you sell this exact kit minus the joints and misalignment spacers? I still want the tube adapters jam nuts and everything else but I would rather have a cartridge joint than a heim joint.

Asked by: Justin - 5/13/2017

A: Yes you can order the Tubing, Tube adapters, Jam nuts, and Brackets separately . They are just not sold as a pre-bundled kit

Was this answer helpful? 1 of 1 Customer(s) found this Answer helpful.

Answer provided by: Tom Kellough (7/19/2017)

Submit an answer

Q: Does this kit require gas tank modification on the 4dr jk?

Asked by: Clifford swartz - 11/7/2017

A: The JK would need to have the gas tank relocated to the rear of the Jeep

Was this answer helpful? 1 of 1 Customer(s) found this Answer helpful.

Answer provided by: Tom Kellough (11/27/2017)

Submit an answer

Q: Will I need a body lift for the link bracket to clear my Jeeps tub ?

Asked by: Brian - 6/18/2020

A: Yes, the Dual 4 Link typically requires a 1" body lift on a TJ or YJ. Most likely the same on other models.

Was this answer helpful? 0 of 0 Customer(s) found this Answer helpful.

Answer provided by: Armando Verdugo (6/18/2020)

Submit an answer

Q: do you have a axle truss for a stock cj7 axle?

Asked by: Matt - 2/3/2021

A: We do not have any truss's made specifically for any Jeep CJ axles

Was this answer helpful? 0 of 0 Customer(s) found this Answer helpful.

Answer provided by: Tom Kellough (2/4/2021)

Submit an answer

Q: looking for 4 bars only t for a c4 vette rear end in a hot rod (not triangular) do they have spherical bearings

Asked by: Mike Sawchuk - 3/5/2021

A: Our 4 link hits use a heim joint so there is not bearing in the joint

Was this answer helpful? 0 of 0 Customer(s) found this Answer helpful.

Answer provided by: Tom Kellough (3/5/2021)

Submit an answer

Questions about this item? Ask here.

Easy 4 Link - Kit B - Triangulated Adjustable Uppers

Choose Options

5% off as a Kit vs. Individual parts

Rating Snapshot

Average Customer Ratings

Q: Does this kit work on a 88 jeep wrangler?

Q: DO I NEED A TRAC BAR WITH THIS KIT? I AM USING IT IN THE REAR OF MY JEEP

Q: Will ur 4 link kit work with ur 8.8 axle swap truss that's also triangulated?

Q: Will this kit and kit a work on a 2012 jk? Will I still need a track bar? Any chance on being able to run a different joint like a Johnny joint?

Q: Will you sell this exact kit minus the joints and misalignment spacers? I still want the tube adapters jam nuts and everything else but I would rather have a cartridge joint than a heim joint.

Q: Does this kit require gas tank modification on the 4dr jk?

Q: Will I need a body lift for the link bracket to clear my Jeeps tub ?

Q: do you have a axle truss for a stock cj7 axle?

Q: looking for 4 bars only t for a c4 vette rear end in a hot rod (not triangular) do they have spherical bearings

Accessories

Browse Similar Items

Recently Viewed Items

Mailing List