(0) Item / $0
Call: 855-278-3299 | Hi Guest, Login! |
Front Axle Truss for TJ, LJ, ZJ

Front Axle Truss for TJ, LJ, ZJ

Your Price:$129.99
Call for Availability
Part Number:TJ3001

Choose Options

Axle model
30 Axle
44 Axle
Upper Control Arm Mount
Truss ONLY no UCA mount.
Daystar Bushings [+$90.00]
Currie Johnny Joints [+$140.00]
Also available from these fine distributors

Front Axle Truss for TJ, LJ, ZJ

 This heavy duty and light weight truss system is designed to take serious abuse and reinforce your front 30 or 44 TJ/LJ axle. The 1/4" thick truss top and 10Ga. gusseting incorporates a unique design to strengthen both axle tubes, not just the long tube. The precision cut and formed components of this setup ensure a hassle-free installation. Not only do we offer a truss, but you can also get a COMPLETE POLYURETHANE BUSHING REPLACEMENT for your upper control arms, or you can even upgrade to Currie Johnny Joints.

Axle model options:
  • 30 Low Pinion (Wrangler 1997-2006)
  • 44 Low Pinion (Rubicon Wrangler 2003-2006)
Upper Control Arm Options:
  • Truss ONLY - No bushings/joints/keyed tabs included. Key hole slots on top of truss where keyed tabs would go must be filled with weld. Use this only if you aren't connecting the passenger side UCA or are reusing the factory bracket (see 4th image for details).
  • Daystar  Bushings - Includes bushing, inner sleeve, and thrust washer for Driver side and bushing, weldable outer sleeve, inner sleeve, and two keyed tabs for Passenger side.
  • Currie Johnny Joints - Includes 2.0" Press-in machined Johnny Joint (CE-9112M), 2.0" weldable Johnny Joint (CE-9112), and two keyed tabs for Passenger side. Both joints include greasable bolts.

Features include:

  • 1/4" and 10 gauge (.130") mild steel. Precision CNC cut and bent for great fitment.*

  • Truss is low profile to allow clearance above the axle.

  • Truss spans length of long side AND short side.

  • Truss is reinforced using interlocked 10 gauge thick gussets for maximum strength and easy assembly.

  • Overall low profile design means your axle is stronger, sleaker, easier to fit into any vehicle, and less likely to interfere with vehicle components.**

NOTE: This kit requires general welding and fabrication skills including welding to the cast center section. Welding should only be done by a competent welder. Artec Industries implies no guarantees or warranties and is not liable for improper installation.
*Some grinding and fitment may be required when installing this kit. Every axle varies slightly and some fabrication may be required.

** In rare and extreme cases, the truss may come into contact with oil pan. Prior to operating the vehicle, remove the coil springs, cycle the suspension including full compression of both sides simultaneously and add bumpstop extensions to prevent damage to oil pan.

5 Stars
This kit rocks. I was worried about it weighing to much when I ordered it. When I got it I was pleasantly surprised how light it is. The top piece is a solid 1/4", the others are thinner. There is plenty of gusseting for strength. The directions are very straightforward and easy to read. Just make sure you put good tacks and don't let it get to hot. I think using this kit is far better than sleeving the axle tube.
Did you find this helpful?  9 of 9 Found Helpful
Reviewed by:  from Windsor, Ca.. on 6/8/2015
5 Stars
Best Truss you can buy
Truss was easy to assemble and not only looks great but added the strength i was looking for. I would & have recommended it to all my wheelin buddies!
Did you find this helpful?  6 of 6 Found Helpful
Reviewed by:  from Dallas,TX. on 4/20/2015
5 Stars
Outstanding product
I ordered the Dana 44 Artec truss with the Currie Johnny Joint to strengthen my new G2 axles and had it installed the same time as my Rock Krawler 5.5 long arm coil over lift kit. Easy install with a professional look and unreal strength.
Did you find this helpful?  6 of 8 Found Helpful
Reviewed by: (Verified Buyer)  from Sumter, SC. on 3/10/2015
5 Stars
Dana hp30 axle truss and upper and lower gussetts
Truss went together good, gussets fit perfect...if your considering this truss no need to wait, just do it. If I can install this kit anyone can.
Did you find this helpful?  5 of 6 Found Helpful
Reviewed by:  from East Texas. on 4/4/2015
5 Stars
Axle Truss
I purchased the Dana 44 front axle truss for a LJ. It fit great. Easy install and great instructions. I read them after I was done. It's a guy thing. I'm a certified welder so it was super easy.
Did you find this helpful?  4 of 5 Found Helpful
Reviewed by:  from Spring Grove,IL. on 4/6/2015

Related Items


TJ 8.8 Swap Kit with Truss
Average Rating(46)
In Stock

Recently Viewed Items

Connect With Us
Newsletter Sign Up
PayPalVisaMastercardAmerican ExpressDiscover
3dcart Design by The Cart Designer